# TouchWin Screen Switching And Animation

Use this P1 reference for TouchWin page switching, PLC-controlled page changes, current-screen reporting, button controls, indicator buttons, and moving/rotating animation.

Source anchors:

- TouchWin editing manual v1.2 PDF page 38: system settings `交互`, `控制画面变换`, `报告当前画面号`.
- TouchWin manual PDF pages 80-81: `4-3-7 画面跳转`, password/permission and enable/display control.
- TouchWin manual PDF pages 65-68: `4-2-10 平移动画`, `4-2-11 旋转动画`, material/visibility behavior.
- TouchWin manual PDF page 56: object animation can move X/Y position by register value.
- TouchWin manual PDF pages 75-77: button and indicator-button operation; avoid PLC direct `OUT` to an HMI-operated bit.

## Page Switching Methods

| Method | Best for | Notes |
|---|---|---|
| `画面跳转` component | Operator button changes page on HMI. | Can set target screen number, password mode, display control, enable control, and delay. |
| System setting `交互 -> 控制画面变换` | PLC controls HMI page. | HMI reads a register; value equals target screen number. After jump, TouchWin clears the register to `0`. |
| `交互 -> 报告当前画面号` | PLC knows current HMI page. | HMI writes current screen number to a register, useful for sequence/diagnostics. |
| Function key/function area | Multi-action button behavior. | Use when a button needs several HMI actions, but keep PLC writes explicit and documented. |

## PLC-Controlled Screen Switching

Recommended allocation:

| Address | Direction | Purpose |
|---|---|---|
| `D100` | PLC -> HMI | Screen command register; value is target page number. |
| `D101` | HMI -> PLC | Current screen report register. |
| `M100` | HMI/PLC command | Request page change, edge driven. |
| `M101` | PLC internal | One-shot or transition lock. |

TouchWin steps:

1. Open system settings for the HMI project.
2. Enter the `交互` page.
3. Enable `控制画面变换`.
4. Set the object/register to the chosen PLC register, for example `D100`.
5. Enable `报告当前画面号` and set a different register, for example `D101`.
6. Download and test with offline/online simulation where available.

PLC-side rule:

- Write the target page number with an edge/event, not every scan.
- Expect TouchWin to clear the screen command register to `0` after the jump.
- Do not use the same register for command and current-screen report.

Example ladder plan:

| Network | Logic |
|---|---|
| Page request | HMI/PLC event sets `M100`. |
| One-shot | `M100` rising edge writes `K10` to `D100` for page 10. |
| Clear request | Reset `M100` after command or after `D101 = K10`. |
| Timeout alarm | If `D101` does not become `K10` within a timeout, set an HMI communication/screen alarm bit. |

## Manual HMI Button Page Jump

Use `部件 -> 操作键 -> 画面跳转` or the component toolbar:

1. Place the `画面跳转` component.
2. Set `跳转画面号`.
3. Choose password mode if the page is maintenance/parameter/safety related.
4. Use display/enable control when access depends on mode, alarm, or user permission.
5. Name the button by destination: `主画面`, `参数`, `报警`, `手动`, `维护`.

## Button And Indicator Button Control

| Component | Use | Caution |
|---|---|---|
| `按钮` | Write/toggle/set/reset a bit. | It does not display final bit state by itself. |
| `指示灯按钮` | Operate one bit and display a bit state. | Operation object and monitor object can be separated; prefer separating command and status. |
| `指示灯` | Display a bit/register state. | Use for actual PLC status, not command request alone. |

Important rule from the TouchWin manual: when the HMI operates a lower-device bit, avoid using a direct PLC `OUT` instruction on the same bit. Use a command bit from HMI and a separate PLC-controlled status/output bit.

## Moving Object Animation

Use either object X/Y animation or a `平移动画` component.

### Object X/Y movement by register

Some objects expose animation settings:

- `横向移动`: display X coordinate = original X + register value.
- `纵向移动`: display Y coordinate = original Y + register value.

Recommended for simple cart/tank/slider motion:

| Address | Meaning |
|---|---|
| `D200` | X offset in pixels or engineering-scaled display units. |
| `D201` | Y offset if needed. |
| `M200` | Animation enable. |
| `M201` | Reset animation position. |

PLC pattern:

1. Use a timer pulse to increment/decrement `D200`.
2. Clamp `D200` between minimum and maximum display offsets.
3. Reset `D200` to zero on homing/reset or page entry.
4. Use separate real machine position when animation reflects actual equipment; do not let display animation become the control source.

### `平移动画`

Use when the object should follow a drawn path.

1. Place/draw the visible object or image.
2. Add `平移动画`: `部件 -> 动画 -> 平移动画`.
3. Draw the path; double-click to finish.
4. Select the object and animation path, then group them.
5. Configure duration/cycle time.
6. Configure `许可信号`, `复位信号`, and `重复` as needed.

### `旋转动画`

Use for fan/motor/agitator-style display:

1. Add `旋转动画`.
2. Add images/materials for the rotation frames.
3. Set cycle time.
4. Use a coil enable so the animation runs only when the corresponding PLC run status is ON.
5. Use reset/visibility control for fault or stopped state.

## Cart Animation Template

| PLC/HMI address | Purpose |
|---|---|
| `M300` | Cart run command. |
| `M301` | Cart moving right status. |
| `M302` | Cart moving left status. |
| `M303` | Cart home sensor status. |
| `M304` | Cart fault status. |
| `D300` | Cart displayed X offset. |
| `D301` | Cart actual position or simulated position. |

HMI:

- Bind the cart image horizontal animation to `D300`.
- Display run/fault status with indicator lights.
- Add manual jog buttons writing command bits, not direct output bits.

PLC:

- If real position is available, scale actual position into `D300`.
- If only demonstration animation is needed, increment `D300` while moving and reset at ends.
- Add limit checks; never use the HMI animation value as the only safety limit.

## Verification Checklist

- Offline simulate screen jump buttons.
- Online simulate PLC register-driven page jump if supported.
- Confirm command register clears to `0` after page jump.
- Confirm current-screen register updates correctly.
- Confirm animation enable/reset bits work.
- Confirm HMI command bits are not also driven by PLC `OUT`.
- Download to HMI, verify PLC communication, then test alarms/permissions.